• 877-412-3667 9AM - 3PM CST

  • ORDERS OVER $200 SHIP FREE - CONTINENTAL US ONLY

Navigate to the Automatic Door and Hardware homepage

USA Company
​Located in Texas

How To Install A Handicap Door Opener

How To Install A Handicap Door Opener | Sales: [email protected]

In this article we explain how to install a commercial handicap low energy door opener. Low energy door openers provide equal accessibility for all pedestrians. They transform a manual door into a barrier free automatic door. For this installation we will be explaining in detail how to install the Commander low energy door opener with an outswing push arm.

1. Remove Drive Assembly

The drive assembly consists of a motor, gearbox, and controller. All these components are attached to the door opener's back plate by 4 allen screws. Begin by removing all 4 allen screws so that the back plate is exposed.




2. Install Back Plate

All commercial grade automatic door openers install top jamb. Meaning, the door operator is designed to mount at the top of the door frame head. For a push arm style door operator, be sure to mount the back plate on the push side of the door frame. The back plate should be mounted at the top of the door frame head, and flush at the bottom. The back plate should overhang the door frame by 1.5" on each side. Self tapping screws can be used to secure the back plate to the door frame. The back plate does have pre-drilled holes, however be sure the back plate is well secured as it will be holding the weight of the drive assembly.



3. Re-Install Drive Assembly

Once the back plate is secured to the top of the door frame, re-install the drive assembly using the 4 allen screws we previously removed. A 5mm allen wrench can be used. On the back of the drive assembly is a key slot which is designed to slide over an alignment screw located at the center of the back plate. Please note the controller side of the drive assembly should always be towards the hinge side of the door. If not, the drive assembly is in upside down and must be rotated.





4. Determine Reveal

Reveal is the distance from the face of the door to the face of the door frame. Reveal is dependent on the door jamb width. Most commercial doors have a 5-3/4" jamb depth, however others can have jamb depths up to 8-1/4" or more. The larger the door jamb depth, the greater the reveal. The standard Commander outswing arm is suitable for reveals from 0" to 8". If the door application has a deeper reveal than 8" a special extension arm can be utilized.



Once the reveal is determined, the telescopic arm assembly must be adjusted to the proper length. For a 0" reveal the telescopic arm should be adjusted to 13". For each inch of reveal, the telescopic arm would need to be adjusted an additional inch. For example, a 1" reveal would require an arm length of 14", and so on. We recommend laying the arm out on a table or the floor when a measuring the arm length. Once the desired arm length is found, mark the location on the arm with a pencil. Do not tighten the screws in the arm to secure the arm length yet.



5. Mount The Arm

Mount the arm portion with the spindle on to the door opener's gearbox. To do this be sure to attach the arm 20 degrees past perpendicular towards the hinge side of the door. This will allow you to preload the spring later on.



Next, mount the door shoe onto the door. The door shoe should be mounted 13.5" from the inside door hinge jamb.


Join both arms together and line up the telescopic arm so it is at the length you marked previously with the pencil mark. You will feel resistance as you push the main arm assembly towards the telescopic arm as you are preloading the internal fire spring within the door opener's gearbox. Secure the arm screws so that the arm is now one piece and secure.


6. Connect Main Power

The Commander door opener is 120VAC, Single Phase, 60 Hz. Connect the line voltage, neutral, and ground. Be sure the door opener is "off" before making power connection.


7. Connect Other Door Opener Accessories

At this time you can connect your other door opener accessories such as wireless activation switches, touchless activation switches, safety sensors, electric strike locks, etc.

8. Perform The Learn Cycle

We are now ready to do the learn cycle or initial set up. This process allows the microprocessor controller to measure the door weight and size of the door, then automatically setup it's parameters for that door size. When the learn cycle occurs there should be no obstructions in the path of the door swing. The door should not be touched when the learn cycle occurs. If the learn cycle is interrupted, you will have to start over from the beginning.



First, turn the door opener "on". Next identify SW1 push button switch on the controller. Press and hold it for about 5 seconds. Once you notice the red LED (LD2) flashing rapidly, you may release SW1 push button. The door will slowly open, recycle partially, close, and then reopen.

Once the door is completely closed, the learn cycle is complete and you can test the door operation by using your activation switch. Always be sure to verify that the speed and closing adjustments are suitable for your door application.

The Commander low energy door opener is by far the easiest door opener to install due to the simplistic design and self tuning / self learn set up. If you need an automatic door opener, then the Commander automatic swing door operator is the best choice. Order today and receive FREE shipping!

Disclaimer: The material in this article has no regard to the specific installation, building code requirements, law requirements, authority having jurisdiction, local or state requirements, or any particular needs of any viewer. This article is presented solely for informational and entertainment purposes and is not to be construed as a recommendation or solicitation. Nor should any of its content be taken as advice. Automatic Door and Hardware is not an installation advisor. The views expressed in this article are completely speculative opinions and do not guarantee any specific result. Commercial doors, hardware, and automatic door parts should only be worked on by trained, qualified, and licensed professionals; failure to do so can result in danger. Any opinions expressed in this article are subject to change without notice. Automatic Door and Hardware is not under any obligation to update or keep current the information contained herein. Automatic Door and Hardware may have an interest in the securities and commodities of any entities referred to in this material. Automatic Door and Hardware accepts no liability whatsoever for any loss or damage of any kind arising out of the use of all or any part of this material. Automatic Door and Hardware recommends that you consult with a licensed and qualified professional before making any modifications or repairs to commercial doors, automatic doors, or hardware components of those doors. The content covered in this article is NOT to be considered as advice. I’m NOT an adviser. These are only my own personal and speculative opinions, ideas, theories, hypotheses, charts, technical analysis, insights, and curated news publications. The technical analysis in this article is completely speculative and does NOT guarantee any specific result. The technical analysis in this article has NO proven rate of accuracy. Do NOT repair or modify your doors and/or hardware based upon the analysis presented in this article. Always do your own research and only use trained and licensed professionals for any repairs or modifications. I will NOT be held liable for any of your personal repairs or modifications or any losses/damages that you may incur if you do repair or modify your doors and/or hardware. Information provided through this article is provided to you as is without any express representations or warranties of any kind, and we make no representation or warranty that this article (or any information provided in response to your inquiry), will be accurate, complete, or error-free. You agree that you must evaluate all information and responses, and that you bear all risks associated with, the use of this article, including any reliance on the accuracy, completeness, or usefulness of any information or materials made available through this article. This article is purely for entertainment purposes only!

Get The Parts That Fit

Filter your results by entering your commercial door's Make and/or Model to ensure you find the parts that fit your door.

Need A Quotation?

Receive A Free Quotation Immediately

Email [email protected] or call 877-412-3667 with the product you are interested in, the quantity, and any other requirements you may have. One of our specialists will email you back a free quotation shortly. Did you know we offer free design help? If you are unsure of the product you need, but know the scope of what function or application you need, our design team can help! Contact us with your inquiry today.