• 877-412-3667 9AM - 3PM CST

  • ORDERS OVER $200 SHIP FREE - CONTINENTAL US ONLY

Navigate to the undefined homepage

USA Company
​Located in Texas

Home > Door Hardware > Panic Bar Exit Devices > Panic Bar Exit Device Help Center > How to Repair a Broken Vertical Rod on a Commercial Panic Bar Exit Device

How to Repair a Broken Vertical Rod on a Commercial Panic Bar Exit Device

How to Repair a Broken Vertical Rod on a Commercial Panic Bar Exit Device

Overview

A commercial panic bar exit device is an essential component in ensuring the safety of occupants in commercial buildings. The vertical rods on a panic bar exit device are responsible for latching the door closed and ensuring that it stays securely shut. However, these vertical rods can become damaged or broken over time, and it is important to repair them as soon as possible to ensure the proper functioning of the panic bar exit device.

In this article, we will provide you with step-by-step instructions on how to repair a broken vertical rod on a commercial panic bar exit device.

Materials Needed

  • Replacement vertical rod
  • Allen wrench
  • Screwdriver
  • Hammer
  • Drill
  • Metal cutting saw
  • Measuring tape
  • Markers
  • Safety goggles
  • Gloves

Steps to Repair a Broken Vertical Rod

  1. Identify the broken vertical rod: The first step in repairing a broken vertical rod is to identify which one is damaged or broken. Once you have identified the rod, remove it from the panic bar exit device.
  2. Remove the end cap: Remove the end cap on the broken vertical rod with an Allen wrench.
  3. Remove the screws: Use a screwdriver to remove the screws that hold the vertical rod in place.
  4. Remove the broken rod: With a hammer, gently tap the rod to loosen it and then pull it out of the panic bar exit device.
  5. Measure and mark the new rod: Measure and mark the new vertical rod to match the length of the old rod. Use a metal cutting saw to cut the new rod to the correct length.
  6. Install the new rod: Insert the new vertical rod into the panic bar exit device and secure it in place with screws.
  7. Conclusion

    In conclusion, a broken vertical rod on a commercial panic bar exit device is a serious problem that requires prompt attention. It can cause a door to become inoperable, which can be a safety hazard in an emergency situation. However, with the right tools and knowledge, it is possible to repair a broken vertical rod without having to replace the entire device.

    First, you must diagnose the problem by inspecting the device and identifying the damaged components. Then, you can remove the damaged parts and replace them with new ones. You may need to adjust the tension on the device and perform a few tests to ensure it is functioning properly.

    If you are not comfortable performing these repairs yourself, it is always best to seek the assistance of a professional. At Automatic Door and Hardware, we offer a wide range of commercial door hardware and repair services to ensure your facility is safe and secure. Contact us today to learn more.

    Commercial door panic bars and exit device hardware are available at www.autodoorandhardware.com.
Disclaimer: The material in this article has no regard to the specific installation, building code requirements, law requirements, authority having jurisdiction, local or state requirements, or any particular needs of any viewer. This article is presented solely for informational and entertainment purposes and is not to be construed as a recommendation or solicitation. Nor should any of its content be taken as advice. Automatic Door and Hardware is not an installation advisor. The views expressed in this article are completely speculative opinions and do not guarantee any specific result. Commercial doors, hardware, and automatic door parts should only be worked on by trained, qualified, and licensed professionals; failure to do so can result in danger. Any opinions expressed in this article are subject to change without notice. Automatic Door and Hardware is not under any obligation to update or keep current the information contained herein. Automatic Door and Hardware may have an interest in the securities and commodities of any entities referred to in this material. Automatic Door and Hardware accepts no liability whatsoever for any loss or damage of any kind arising out of the use of all or any part of this material. Automatic Door and Hardware recommends that you consult with a licensed and qualified professional before making any modifications or repairs to commercial doors, automatic doors, or hardware components of those doors. The content covered in this article is NOT to be considered as advice. I’m NOT an adviser. These are only my own personal and speculative opinions, ideas, theories, hypotheses, charts, technical analysis, insights, and curated news publications. The technical analysis in this article is completely speculative and does NOT guarantee any specific result. The technical analysis in this article has NO proven rate of accuracy. Do NOT repair or modify your doors and/or hardware based upon the analysis presented in this article. Always do your own research and only use trained and licensed professionals for any repairs or modifications. I will NOT be held liable for any of your personal repairs or modifications or any losses/damages that you may incur if you do repair or modify your doors and/or hardware. Information provided through this article is provided to you as is without any express representations or warranties of any kind, and we make no representation or warranty that this article (or any information provided in response to your inquiry), will be accurate, complete, or error-free. You agree that you must evaluate all information and responses, and that you bear all risks associated with, the use of this article, including any reliance on the accuracy, completeness, or usefulness of any information or materials made available through this article. This article is purely for entertainment purposes only!

Get The Parts That Fit

Filter your results by entering your commercial door's Make and/or Model to ensure you find the parts that fit your door.

Need A Quotation?

Receive A Free Quotation Immediately

Email [email protected] or call 877-412-3667 with the product you are interested in, the quantity, and any other requirements you may have. One of our specialists will email you back a free quotation shortly. Did you know we offer free design help? If you are unsure of the product you need, but know the scope of what function or application you need, our design team can help! Contact us with your inquiry today.